| 1. | Exact and approximate solutions for surface acoustic waves in elastic plate with metal electrode layer
具有电极层无限大弹性板中表面波的精确与近似解 |
| 2. | It is found that the height of the metal electrode , the distance between the source and drain electrodes , the thickness of the sio
研究了场效应纳电子晶体管构造过程中金属电极的结构设计，源-漏电极高度sio |
| 3. | Once the sapphire was covered with nanotubes , they could place the metal electrodes of the transistors wherever they wanted and remove the unwanted nanotubes with highly ionized oxygen gas
蓝宝石上覆盖奈米管后，就可在任意的位置安装电晶体的金属电极，再以高度离子化的氧气除去不需要的奈米管。 |
| 4. | Important information is that the distance between metal electrode and emitting layer must be suitable . too large , difficult injection ; too small , excitons quenching . within 0 - 70ma / cm2 injection , no effect was observed
实验给出影响受激发射的重要信息：金属电极距增益区距离要适当，太大，器件厚，电注入困难；太小发光激子在电极猝灭。 |
| 5. | Results of the model tests show that ekg can be used to improve the drainage property and increase the undrained shear strength of cohesive fill , and conductive plastics can get rid of the corrosion that happened in metal electrode
得出研制出的导电塑料应用于ekg能克服金属在土中导电时的腐蚀。模型试验结果较为满意。武汉理工大学博士学位论文并提出了ekg加筋的设计方法。 |
| 6. | One was using the cyclic ether to pretreat the lithium metal electrode . and a favorable surface sei film was wished to form on the lithium metal , to enhance the interface stability of lithium electrode and the cycleability of lithium battery
方法一:尝试采用环醚类化合物对金属锂电极进行表面预处理,预先在金属锂表面形成良好的表面sei膜,提高锂电极界面稳定性和锂负极的电化学性能。 |
| 7. | But there are still several problems concerning the stability and reproducibility of device fabrication . the heavily born doped p - type diamond films synthesized by hot filament chemical vapor deposition with b ( ch3 ) 3 as boron source substituted the metal electrode aluminum
本文还利用热灯丝化学汽相沉积( hfcvd )法，采用硼酸三甲酯b ( ch3 ) 3为硼源制备了重掺杂p型金刚石膜，作为lppp / alq异质结增强型发光器的电极。 |
| 8. | The intention of the paper is to study the deposition and properties of znte ( znte : cu ) polycrystalline thin films and to apply znte ( znte : cu ) as a complex back contact layer between cdte and metal electrode to obtain ohm contact and high efficiency cdte solar cells
本论文目的在于研究znte ( znte ： cu )多晶薄膜的制备和性质，并把znte znte ： cu多晶薄膜作为复合背接触层应用于cdte和背金属电极之间以获得欧姆接触和高效cdte太阳电池。 |
| 9. | Zno varistors have been widely used in electronic and electrical power devices and systems because of excellent nonlinear v - i characteristics and high absorbance of electric current surges . with the smt ( surface mounted technology ) development , traditional zno varistors can not meet the multilayer thin films lamination structure nappe varistor ceramics and metal electrode low temperature co - fire need . however , the best character of zno - v2o5 varistor can sinter in common furnace during lower temperature ( 900 ) , not only settling the problem relate to upon , but also saving energy sources
Zno压敏电阻因其优异的v ? i非线性和较高的浪涌吸收能力而广泛应用在电子、电力设备系统上。然而,随着表面贴装技术( smt )的发展,传统的zno压敏陶瓷不能满足多层膜独石结构叠层压敏电阻元件陶瓷与金属电极低温共烧的需要。而zno ? v2o5系压敏陶瓷的最大优点是能用普通烧结炉在较低温度( 900 )下烧结,不仅解决了以上问题,还大大节约了能源。 |
| 10. | The main work in this thesis includes two contents as follow : 1 we have investigated the properties of ohmic contact between metal electrode ( al and ti / al electrode ) and n - gan dealed under different annealing conditions . by using xrd sims analytic methods and i - v measuremnet , we analysed the interface between metals and gan , and suggested that it is effect to decrease the value of the ohmic contact
主要工作如下： 1 、研究了al单层及ti al双层电极与n型si基gan和al _ 2o _ 3基gan在不同退火条件下的欧姆接触情况，并用x射线衍射谱( xrd ) ，二次离子质谱( sims )对界面固相反应进行了分析。 |
